Exactly How to Install a Bath Tub in Your Bathroom
Exactly How to Install a Bath Tub in Your Bathroom
Blog Article
Each person may have their personal thinking involving How to Install a Bathtub Yourself.
Mounting a tub isn't precisely rocket science, yet it does need solid plumbing, woodworking, as well as in some cases, tiling abilities. Replacing an old bath tub with a brand-new one is also a reasonably tough project. If the old bathtub is easily accessible, the task can move speedily; if you need to open a wall surface to get rid of the old tub and place the new bath tub, the task is a lot harder. In either situation, the project is within a house handyman's skills, although you will certainly need a helper to vacate the old tub and also set in the brand-new one. Make certain you have certified yourself for the work and also are comfortable trying it. As opposed to working with a professional to take over a halfway-completed job, it is much better to take into consideration employing one prior to you start. Possibilities are you may require a professional plumber to make tube connections.
This write-up will certainly help you set up a brand-new tub in your shower room if you have currently acquired a new bathtub and do not require to change the setup of your previous water supply pipelines.
Your devices and product list ought to consist of the following:
Preparing for the Installation
Firstly, the supporting framework supplied with the bathroom needs to be fitted (if required) according to the manufacturer's directions. Next, fit the taps or mixer to the tub. When suitable the tap block, it is very important to make certain that if the faucet features a plastic washing machine, it is fitted between the bath as well as the faucets. On a plastic bath, it is also practical to fit a sustaining plate under the faucets device to prevent strain on the tub.
Fit the adaptable faucet connectors to the bottom of the two taps utilizing 2 nuts and also olives (occasionally supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and afterwards pass the electrical outlet via the hole in the bathroom. Use the nut supplied by the producer to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the adaptable overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which should be fitted inside the bath. Ensure you utilize all of the supplied washers.
Link the trap to the bottom of the waste outlet on the bathtub by winding the thread of the waste outlet with silicone mastic or PTFE tape, as well as screw on the trap to the outlet. Link the bottom of the overflow tube in a similar manner.The bath should now be ready to be suited its last placement.
Removing Old Touches
If you require to change old faucets with brand-new ones as a part of your installment, after that the first thing you must do is detach the water system. After doing so, switch on the taps to drain any water continuing to be in the system. The procedure of getting rid of the existing faucets can be rather troublesome because of the restricted access that is often the instance.
Utilize a basin wrench (crowsfoot spanner) or a tap device to reverse the nut that attaches the supply pipelines to the taps. Have a cloth all set for the continuing to be water that will come from the pipelines. As soon as the supply pipes have been gotten rid of, utilize the exact same tool to loosen up the nut that holds the faucets onto the bath/basin. You will require to quit the solitary taps from turning during this process. Once the faucets have actually been eliminated, the holes in the bath/basin will have to be cleaned of any old sealing substance.
Prior to carrying on to fit the brand-new taps, contrast the pipeline connections on the old taps to the brand-new taps. If the old faucets are longer than the brand-new taps, then a shank adapter is needed for the new faucets to fit.
Installing the Bath tub
Utilizing the two wooden boards under its feet, position the tub in the required placement. The wood boards are useful in evenly spreading the weight of the bathtub over the location of the boards as opposed to focusing all the weight onto four tiny points.
The next goal is to ensure that the bath tub is leveled all round. This can be accomplished by checking the level and readjusting the feet on the bathtub till the spirit level reads degree.
To install faucets, fit the bottom of the outermost versatile tap port to the suitable supply pipeline by making a compression join; after that do the same for the other faucet.
Turn on the water supply as well as check all joints as well as new pipework for leaks and tighten them if needed. Fill the tub as well as also inspect the overflow electrical outlet as well as the regular outlet for leakages.
Lastly, deal with the bath paneling as explained in the manufacturer's instruction manual. Tiling and also sealing around the tub needs to wait up until the tub has actually been utilized at the very least once as this will certainly settle it right into its last position.
Suitable New Taps
If the tails of the brand-new faucets are plastic, then you will require a plastic adapter to prevent damages to the string. One end of the connector fits on the plastic tail of the faucet and the other end supplies a connection to the existing supply pipelines.
If you need to fit a monobloc, then you will need minimizing couplers, which links the 10mm pipeline of the monobloc to the standard 15mm supply pipe.
Next, position the tap in the installing opening in the bath/basin making certain that the washing machines remain in place between the tap and the sink. Secure the tap in place with the manufacturer provided backnut. Once the faucet is firmly in position, the supply pipelines can be linked to the tails of the faucets. The taps can either be linked by utilizing corrugated copper piping or with regular faucet adapters. The previous kind must be attached to the faucet finishes initially, tightening up just by hand. The supply pipes can later be connected to the other end. Tighten up both ends with a spanner after both ends have actually been connected.
Tiling Around the Bath tub
In the location where the bathroom fulfills the floor tile, it is needed to secure the accompanies a silicone rubber caulking. This is essential as the fitting can move enough to crack a rigid seal, causing the water to penetrate the wall between the bathroom and also the tiling, bring about issues with moisture and also feasible leakages to the ceiling listed below.
You can choose from a variety of coloured sealers to assimilate your components as well as fittings. They are sold in tubes and cartridges, and can securing gaps approximately a size of 3mm (1/8 inch). If you have a bigger space to fill up, you can fill it with twists of drenched paper or soft rope. Bear in mind to constantly fill up the bathtub with water prior to securing, to permit the activity experienced when the tub is in use. The sealer can split relatively early if you do not take into account this movement prior to securing.
Additionally, ceramic coving or quadrant tiles can be made use of to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and also cut to dimension, are additionally easily readily available on the marketplace. It is recommended to fit the tiles making use of waterproof or waterproof adhesive as well as grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I came across that article about How to Install a Bathtub Yourself while perusing the internet. Sharing is good. You won't know, you will be helping someone out. Thanks a lot for your time. Visit us again soon.
Source This Article Report this page